How To Remove A Youmaker Phone Case

UPDATED 12/17/2018

If yous have an iPhone, y'all more than likely employ or will use a case to protect it. That ways, at some point you'll have to figure out how to install your case and how to remove information technology. It may seem pretty straight forward but if your case is super class plumbing fixtures and/or a snap-on case, it might be a piffling more hard than information technology seems. Good news though – it's not that hard if you lot have some helpful tips. Better news – we have all those helpful tricks laid out below in our step-by-step guides.

How to Put On an iPhone Case

Step 1 - preparing your workspace

i. Prepare by clearing off your workspace and laying down a soft surface

Pull up a seat up at the table, move aside whatsoever unnecessary clutter and most importantly, embrace your firsthand workspace with something soft, like a folded towel. The last thing you desire to do is driblet your phone on the flooring or a hard surface and impairment your device. (Allow's not forget this the whole reason why you lot accept a case to begin with)

Step 2 - slip the top left corner on

2. Skid the iPhone into the top-left edge of the example

Catch the example (opening side upwardly) with your left hand and with your right, catch the phone (screen side up). Slowly slide the top left corner of your iPhone into the case towards the ringer and book button cut-outs/button covers. Don't worry if these elements aren't perfectly aligned at the moment – they will snap in place a little later on. Gently pinch and hold this position with your left paw.

Step 3 - snap the top right corner on

3. Snap in the peak-right corner, followed by the bottom-right corner

With the top-left corner however insert and pinched, use your right hand to snap in the peak-right corner of the case. Then, slide your right mitt downwardly the side of the phone and case applying constant force per unit area, until you get to the lesser-right corner. At present, give this corner a good potent pinch betwixt your alphabetize finger and thumb. It should snap right into place.

Step 4 - secure the final corner

4. Secure and snap in the final, bottom-left corner

Depending on the phone example, securing the final corner may be every bit unproblematic as a gentle pinch on the terminal edge. If not, and the corner of the case is folding underneath the telephone, attempt using a concern card to slide the instance on the concluding edge. Sideslip the business carte du jour into the gap between the iPhone and example, and then slowly move it along the border of the iPhone towards the terminal corner, while simultaneously working to snap the example on. This works sort of like a shoe horn.

Step 5 - make sure cut outs are aligned

5. Confirm that all of the cut-outs and/or push covers align

At this point, the case should be fully installed, which means all of the cutouts/button covers properly align to all of the buttons and ports.

Pro-tip: Sometimes in the process of putting on your case, you may accidentally toggle the ringer on or off, then give that a quick check.

---

Now that you lot have the instance on, it's inevitable that you will have to take if off at some point in the futurity. Mayhap you lot desire to attempt a different instance or maybe you lot're looking to requite yours a quick clean. Whatever the reason, if you need a simple how-to on safely removing your iPhone instance, we can assist with that too. We're breaking down this process pace-by-step.

How to Have Off an iPhone Case

Step 1 - preparing your workspace

1. Set up past clearing off your workspace and laying down a soft surface

Much similar removing a instance, it'south important to get situated and properly set up. So catch a seat, articulate off your workspace and lay downward a towel to create a soft, flat working surface. The final affair you want to practice when removing your example is to drop and scissure your phone.

Step 2 - removing the corner diagonally opposite the volume buttons

2. Begin by removing the corner diagonally opposite to the volume buttons

Start by removing the corner of the case that is catty-corner to the ringer switch and volume buttons. Take hold of your phone similar you're going to send a text and rotate it 180º, keeping the screen side upwards. On this new, top-left corner, place both thumbs on the forepart of the case and firmly pry the case away from the phone. If this doesn't work, carefully try using your fingernails, or a dull object, to release the edges nearest to the corner.

Step 3 - remove adjacent corner

3. Remove the directly adjacent corner

With the phone in the same position, apply the techniques mentioned above to remove the corner directly adjacent to the prior. The instance should come up off a little easier on this corner, then accept extra precaution every bit to not driblet your phone.

Step 4 - slide the phone out of the case

iv. Take hold of the telephone and slide information technology out of the case

With the two corners dislodged, gently hold the case with one paw and with the other, become a firm grip on the freed role of the telephone. Now, just slide the phone out and away from the example.

Pro-tip: Double check that you didn't toggle the ringer switch or creepo upward the volume in the process of removing your case.

---

So there you lot have information technology. You're now an expert at putting on and removing an iPhone instance. If yous have any trouble, or helpful tips nosotros did not mention, nosotros'd dear to hear from you. Just send an email to hullo@totalleecase.com

These are correct up your aisle.